Manual abstract Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage.

1. Manual High School Peoria Il

Regularly wipe the front of the appliance and panel with a damp cloth; water and a little washing-up liquid will suffice. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Never use other chlorinated household detergents! Health hazard! Salt and rinse aid Check the refill indicators 6 7. If required, top up the salt and/or rinse aid.

En Filters Waste which is deposited on the filters 27 may result in a blockage. After each washing cycle check the filters for residue. Unscrew the filter cylinder and remove the filters.

The filters are permanently attached to each other and cannot be dismantled. Remove large foreign objects. Clean the filters under running water.

Re-installation: Insert the filters and screw the filtercylinder tight. Spray arms Lime and remnants of food in the washing water can block the nozzles in the spray arms 22 and 24 and the arm mountings. Inspect the nozzles in the spray arms for blocked holes due to remnants of food.

If necessary, pull the lower arm 24 upwards and lift it off. Unscrew the upper spray arm 22. Clean both spray arms under running water.

Refit the spray arms. Ensure that the lower arm has locked into place and the upper one is screwed tight. Spray arms en Waste water pump. some models Large food remnants in the rinsing water not retained by the filters may block the waste water pump. The rinsing water is then not pumped out and covers the filter. In this case: Set the main switch 1 to OFF. Scoop out any water.

Remove the filters 27. Remove the cover. Check the inner compartment for foreign objects and, if required, remove foreign objects. Re-insert the cover. Re-insert the filters and screw into position. 2click3 en Fault finding Resolving minor problems yourself Experience has shown that you can resolve most problems that arise during normal daily usage yourself, without having to call out a service engineer. Not only does this save costs, but it also means that the appliance is available for use again that much sooner.

The following list of common occurrences and their remedies should help you identify the causes of most problems. Attention Remember: Repairs may be carried out by a technician only. If a component has to be replaced, ensure that only original spare parts are used.

Improper repairs or use of non-original spare parts may cause considerable damage and put the user at considerable risk. When the appliance is switched on The appliance does not start. The mains fuse has tripped. The appliance plug has not been inserted.

The appliance door has not been shut properly. The tap has not been turned on. The filter on the water supply hose is blocked. Switch off the appliance and pull out the mains plug.

Turn off the tap. Then clean the filter which is situated at the connection of the supply hose. Finally, restore the power, turn on the tap and switch on the appliance.

With the appliance itself Lower spray arm rotates with difficulty Spray arm is blocked by small items or food remains. Lid in detergent compartment cannot be closed Detergent compartment has been overfilled. Mechanism is clogged with remnants of detergent. Indicator lamps do not extinguish after washing has finished. “Check water supply” display 8 lights up.

Manual High School Peoria Il

Tap turned off. Water supply interrupted. Filter in the water supply blocked. Supply hose kinked.

Pump is jammed. Remnants of detergent stuck inside dispenser Compartment was damp when it was filled up with detergent.

Compartment must be dry before detergent is added. Indicator lamps do not extinguish after washing has finished Main switch is still set to ON. En Refill display does not light up. Rinse aid refill indicator switched off. (see auto 3in1 chapter) Salt refill indicator switched off.

(see auto 3in1 chapter) Water remains inside appliance after programme has ended Blockage or kink in drainage hose. Pump is jammed. Filters are blocked. The programme is still running. Wait for the programme to end (numerical display will indicate 0).

Perform “Reset” function. During washing Unusual amount of foam is created Normal washing up liquid has been poured into the rinse-aid container. Remove any spilled rinse aid with a cloth as it could otherwise lead to excessive foaming during the next washing cycle. Appliance stops suddenly while washing is taking place Cut in electricity supply to appliance. Water supply has been interrupted.

Implement the “RESET” function. Knocking sound can be heard while washing is taking place A spray arm is knocking against the dishes inside the appliance. Rattling sound can be heard while washing is taking place Crockery has not been stacked properly inside the appliance.

Knocking sound coming from inlet valves This is caused by the way the water pipes have been laid and it has no effect upon the way the appliance fu.Other models in this manual: (2.44 mb) (2.44 mb).